Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Excelsior, CA
Gate installation in Excelsior usually means fitting a custom or semi-custom gate into a narrow side yard between two 1920s stucco houses, often on a slope, with rust from the fog already working on every unpainted surface. We’re Gate Repair Crocker-Amazon, and we’ve served Excelsior since 2016. Most Excelsior jobs start because an original iron or chain-link gate from the 1940s or 1950s has sagged past the point of repair, or because a landlord needs a secure, code-compliant entry on a two-unit flat. We install, repair, and automate gates across all nine major brands, so a single call handles the whole job. Call (833) 842-7897 for a free estimate.
Why Excelsior Homes Are Different
Excelsior’s housing stock is dense and old. The neighborhood is mostly 1920s to 1950s stucco-over-wood-frame houses and two-unit flats, and the lots were cut narrow. That means most gates sit in side yards that are three to five feet wide, wedged between a house wall and a shared property line. When a gate comes off its hinges or a post leans, there is rarely room to work a stock replacement into place. The gate usually has to be cut, welded, or shimmed on site to match the actual opening, which by now has shifted a half inch or more from when the house was built.
The climate adds a second layer. Excelsior sits in a fog belt, and the salt-laden air rolling in from the coast settles on iron and chain-link. Hinges corrode faster here than in the Mission or Noe Valley. We regularly see gate posts that look solid from the top but are eaten through just below grade, where damp soil and old concrete hold moisture against the steel. A gate that won’t close cleanly in Excelsior is often not a hinge problem at all – it’s a post losing its footing. That changes the repair from a twenty-minute re-hang to a footing replacement, and it’s why we always check the post base before quoting a fix.
Terrain matters too. The streets climbing toward McLaren Park were graded steep, and many of those side-yard gates were originally set into sandy fill rather than compacted soil. A gate that sags on a slope near Excelsior Avenue or Persia Street has usually pulled its post over slowly, year after year, until the latch no longer lines up. Re-hanging the gate without addressing the post just buys a few months. We re-pour footings where the soil has given way, and we size the new post for the actual wind and weight load on that specific slope, not a flat-lot formula.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Excelsior Services
Two services cover most of what Excelsior property owners call us for: repair of an existing gate that has failed or sagged, and electric gate repair when an automated operator stops responding. Each has its own dedicated Excelsior page, because the problems and the pricing are different enough to deserve separate detail.
Gate Repair in Excelsior
When an Excelsior gate drags on the sidewalk, binds against the stucco, or will not stay latched, the cause is usually one of three things: a rusted hinge, a post that has shifted in the old concrete, or a gate frame that was welded in the 1950s and has finally fatigued at a corner. We repair all of it. On the narrow side yards common around Excelsior, we often cut and re-weld the frame to match the actual opening rather than forcing a stock replacement into a space it was never designed for. We also replace hinges, posts, latches, and chain-link fabric, and we do it for both the original iron gates and the newer tube-steel gates that replaced many of them. Gate Repair in Excelsior covers the full breakdown, including same-day service options and what a typical re-hang costs on a sloping lot.
Electric Gate Repair in Excelsior
Excelsior has a large stock of automated gates, many of them added in the last ten to fifteen years as landlords replaced manual side gates on multi-unit flats. When a LiftMaster arm stops responding or a FAAC operator trips its breaker, the fault is usually in the control board, the safety loops, or a motor that has been fighting the fog and salt for years. We diagnose the whole system, not just the visible mechanics. That includes loop detectors buried in the driveway, access-control keypads mounted on stucco walls, and the wiring run through old conduit. Electric Gate Repair in Excelsior walks through the diagnostics, the most common failure points, and what a control board or loop replacement costs in this part of the city.
Gate Installation in Excelsior
Most new gate installations in Excelsior are replacements for gates that were built with the house, and they share a common problem: the opening is no longer square, and the old post footings are failing in the sandy fill. A new gate here is rarely a bolt-in job. It involves measuring the actual opening in three places, cutting or welding the frame to fit the irregular lot lines, and often pouring a new post base before anything gets hung. The damp, salty air also dictates materials. We steer Excelsior clients away from uncoated steel and toward powder-coated aluminum or galvanized steel with sealed welds, because those are the materials that survive a decade of fog without rusting through. We install automatic and manual gates, driveway and pedestrian gates, and we fit them to the specific slope, setback, and access needs of each property. For the full scope of this work, see our Gate Installation page.
Automatic Gate Installation
Signs you need it
You’re opening and closing a heavy gate by hand every time a tenant, delivery driver, or family member arrives, and the manual routine no longer works for how the property is used.
What it costs in Excelsior
Automatic gate installation in Excelsior typically runs $1,800 to $3,200 for a single swing arm or slide operator, including the operator, brackets, safety sensors, and basic wiring to a nearby outlet.
How we do it
We mount the operator, set the travel limits, install the safety loops or photocells, wire the control board, and test the full open-close cycle until the gate reverses cleanly on obstruction.
Electric Gate Installation
Signs you need it
You have a manual gate in good structural shape and want to automate it, or an old operator has failed and the gate itself is worth keeping.
What it costs in Excelsior
A full electric gate installation in Excelsior, including the operator, control board, safety devices, and electrical hookup, typically falls between $1,800 and $3,200 depending on gate weight and power access.
How we do it
We assess the gate’s weight and hinge condition first, then install an operator matched to that load, run the low-voltage and line-voltage wiring, and calibrate the travel and force settings.
Driveway Gate Installation
Signs you need it
The existing driveway gate has rusted posts, a frame that is no longer square, or a width that does not fit a modern vehicle.
What it costs in Excelsior
Driveway gate installation in Excelsior, including a new galvanized or aluminum gate and new posts set in concrete, typically starts around $1,800 and rises with width, automation, and the condition of the existing driveway edge.
How we do it
We remove the old gate and posts, set new posts in deeper concrete footings sized for the slope, hang and square the new gate, and add an operator if the job calls for it.
Sliding Gate Installation
Signs you need it
The driveway slopes or the setback is too tight for a swing gate, so a sliding gate is the only workable option for securing the entry.
What it costs in Excelsior
Sliding gate installation in Excelsior typically runs $2,200 to $3,400, including the track or cantilever hardware, the gate panel, and the operator for automated setups.
How we do it
We set the track or cantilever posts, level the rail to the driveway’s slope, hang the gate, install the operator and safety loops if specified, and adjust the travel limits to stop exactly at the open and closed positions.
What Gate Installation Costs in Excelsior
| Item | Typical range in Excelsior |
|---|---|
| Manual driveway gate with new posts | $1,800 – $2,600 |
| Automatic swing gate with operator and safety sensors | $1,800 – $3,200 |
| Sliding gate with track and operator | $2,200 – $3,400 |
These are installed prices for typical Excelsior side-yard and driveway openings. The final number moves with materials, automation, and any footing work the slope requires.
How long does a gate installation take in Excelsior?
Most Excelsior installations take one to two days once materials and any required permits are in hand. Custom-welded gates and jobs needing new concrete footings can add a day. We quote a schedule before work begins. Call (833) 842-7897 for a written estimate.
Do I need a permit to install a gate in Excelsior?
Permit requirements depend on gate height, whether it is automated, and its placement along the property line. We advise on what the city requires for your specific setback and handle the paperwork where a permit is needed. Call (833) 842-7897 and we’ll check your property.
Brands We Service in Excelsior
We service LiftMaster, FAAC, BFT, and Linear systems across Excelsior, along with five other major gate brands. Because we stock common boards, arms, loops, and safety edges for these brands locally, most Excelsior repairs do not wait on a parts order. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Excelsior, CA
| Service | Typical range in Excelsior |
|---|---|
| Gate repair (hinge, latch, or sag fix) | $180 – $340 |
| Post replacement with concrete footing | $400 – $900 |
| Electric gate diagnostic visit | $90 – $150 |
| Control board replacement | $350 – $650 |
| Loop detector replacement | $300 – $600 |
| Operator motor replacement | $500 – $1,100 |
| Automatic gate installation | $1,800 – $3,200 |
| Driveway gate installation with posts | $1,800 – $2,600 |
| Sliding gate installation | $2,200 – $3,400 |
Two things push Excelsior prices upward compared with flatter parts of the city: slope work that requires deeper or wider footings, and rust repair on gates and posts that have spent decades in the fog. Every quote is fixed and agreed before we start, so the number we give you is the number you pay.
Neighborhoods We Serve in Excelsior
We work throughout Excelsior’s 94112 zip code, from the flatter blocks near Mission Street up to the steeper streets climbing toward McLaren Park. The terrain changes quickly here, and so do the footing conditions, which is why we quote each job from the actual site rather than from a map.
- Excelsior District core (Mission Street corridor)
- McLaren Park side streets
- Persia Street and the blocks near Excelsior Avenue
- Naples Street and the southern flat grid
- Geneva Avenue corridor
We typically reach most Excelsior addresses the same day for urgent repairs, and we schedule installations around your availability, not ours.
Service Area – Cities Near Excelsior
Gate Repair Crocker-Amazon serves Excelsior and the surrounding neighborhoods. If your property is just over the district line, we also cover Crocker-Amazon, CA, Outer Mission, CA, Bayview, CA, and Diamond Heights, CA. Call (833) 842-7897 to confirm we’re in your area.
Serving Excelsior, CA – Our Local Coverage Area
We’re based in the Excelsior area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Excelsior
Yes. We cover the full 94112 zip code, from the Mission Street corridor to the steeper blocks below McLaren Park. Those hillside streets often need deeper post footings because of the sandy fill, and we quote each job after seeing the actual grade. Call (833) 842-7897 to schedule a site visit.
Yes. The original iron and chain-link gates on 1920s through 1950s homes and flats are the bulk of our repair work here. We handle rusted hinges, shifted posts, and gates that were custom-welded to lot lines that are no longer what the city records show.
Call (833) 842-7897 and describe what the gate is doing. We’ll ask a few questions about the gate type, the brand if it’s automated, and the slope of the entry, then give you a free estimate. Repairs can often be scheduled the same day, and installations are quoted in writing before any work begins.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Excelsior Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Ramon Hernandez"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Kevin Chen"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
- Henry Kim