Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across San Bruno
Electric gate repair in San Bruno typically costs $220 – $680 depending on whether you need a control board replacement, motor rebuild, or post realignment. Most jobs in the 94066 zip code are diagnosed and repaired in a single visit because we arrive with brand-specific parts for LiftMaster, FAAC, Linear, and BFT systems. If your gate is stuck open, dragging on the ground, or refusing to close after the rain, call (833) 842-7897 for a free estimate. We know San Bruno’s gates and the ground they sit on.
San Bruno sits on the San Andreas Fault zone, and that fact shapes nearly every repair call we take here. Gate posts heave, concrete footings shift, and operators that worked fine last summer suddenly strain against a gate that no longer hangs plumb. We’re not a general handyman service trying to figure out your gate on the fly. We’re Electric Gate Repair specialists who diagnose the whole system: the operator, the hinges, the posts, and the ground beneath them.
Why Gate Repair Crocker-Amazon Is San Bruno’s Preferred Electric Gate Repair Company
Our reputation in San Bruno was built one gate at a time, across neighborhoods that range from the flat lots near El Camino Real to the steep hillside homes above San Bruno Avenue. We’ve rebuilt operators in Crestmoor, replaced control boards near San Bruno Park, and re-set posts in Portola Highlands. San Bruno property owners call us because we’re already familiar with how their specific brand of equipment behaves when the ground moves.
Clay Rasmussen, who leads our team, has built Gate Repair Crocker-Amazon around a single principle: diagnose the fault before ordering a part. San Bruno homeowners appreciate the difference when a technician shows up and already knows the failure patterns of an older LiftMaster swing operator or how BFT hydraulic systems respond to cold, damp coastal air. We run a focused shop. Gate repair is all we do. That narrow depth means faster diagnosis and fewer return visits, and the reviews from San Bruno customers repeatedly note the same thing: we fixed it right the first time because we knew what we were looking at.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Opener Repair in San Bruno
Gate opener repair in San Bruno often comes down to one of three things: a failed control board, a motor that’s been overworked by a binding gate, or a limit switch that’s drifted out of adjustment after a seismic jolt. Most opener repairs in the 94066 zip code run $280 – $520 when we’re rebuilding the motor or replacing a board on a LiftMaster, FAAC, or Linear system. The telltale signs we hear from San Bruno homeowners are the opener humming but not moving, the gate stopping halfway, or the remote working only from a few feet away.
We never replace an opener without first checking the gate itself. A gate that’s binding because a post heaved after winter rain will burn through a new motor in six months. That’s the kind of diagnosis that separates a specialist from a parts-swapper.
Control Board Diagnostics
Older operators in San Bruno, especially LiftMaster and Linear units from the early 2000s, have boards that fail after voltage spikes during winter storms. When we replace a control board, we also check the capacitor and the transformer, because replacing the board alone on a unit with weak supporting components just guarantees a second failure.
Motor and Limit Switch Repair
When a San Bruno gate opener starts stopping in the wrong position or reversing unexpectedly, the limit switch assembly is usually the culprit. We adjust or replace them while the unit is still in place, which keeps the repair cost lower than a full opener replacement.
Automatic Gate Repair in San Bruno
Automatic gate repair in San Bruno covers everything from swing gates on residential driveways to slide gates at apartment complexes and commercial lots near the BART corridor. A typical automatic gate repair in San Bruno runs $260 – $680, with the higher end typically involving control board replacement, loop detector work, or a full operator rebuild on a commercial-grade FAAC or BFT unit. The most common call we get from San Bruno property managers is a gate that won’t respond to a keypad, remote, or phone entry system after a storm.
Safety systems are a major focus here. A gate that’s not reversing correctly when it meets resistance is a liability, especially at multi-unit properties. We test safety edges, photocells, and loop detectors on every automatic gate repair call in San Bruno, not just the visible mechanical components.
Safety Sensor and Loop Detector Work
San Bruno’s fog and rain corrode photocell housings and the underground wiring to loop detectors over time. We excavate, splice, and re-seal connections properly, which is the difference between a repair that lasts five years and one that fails again next winter.
Access Control Integration
For apartment buildings and commercial properties in San Bruno that use DoorKing or BFT systems, we repair and replace keypads, card readers, and phone entry modules. If the operator is functional but the access system isn’t talking to it, that’s a diagnostic challenge we handle directly rather than outsourcing.
Trusted Brands We Service in San Bruno
We work on LiftMaster, FAAC, BFT, and Linear systems every week in San Bruno, and we carry common replacement parts for those brands in our service vehicles. That means a San Bruno customer with a broken FAAC hydraulic arm or a dead LiftMaster control board doesn’t wait for a part to ship from a warehouse. We’re trained on nine gate brands total, including Mighty Mule, Ghost Controls, Viking, DoorKing, and Elite, but the four brands we see most often around 94066 are the ones we stock for. If you’re not sure what operator you have, call us and describe the unit or text a photo; we can usually identify it in seconds.
Common Electric Gate Repair Problems We See in San Bruno Homes
- Heaved posts on clay soil. Flatland neighborhoods near San Bruno Park sit on clay that expands in winter and contracts in summer. A post that rises even half an inch throws the gate out of alignment and makes the operator work twice as hard.
- Corroded safety photocells and loop detectors. Years of fog, rain, and salt air eat through sensor housings and wiring. Gates near the base of the hills see more corrosion than most because the marine layer lingers.
- Legacy control boards failing after voltage spikes. Many San Bruno homes still run original LiftMaster or Linear boards from the 1990s and 2000s. When a winter storm causes a surge, a board that was already aging quits entirely.
- Sagging wood gates on steep lots. Hillside homes above San Bruno Avenue often have heavier redwood gates that have sagged over decades. The weight shift kills hinges and forces the opener to work against its own geometry.
See the difference
Before
After
Before
After
Before
AfterPricing for Electric Gate Repair in San Bruno, CA
Electric gate repair in San Bruno ranges from $220 for a simple limit switch adjustment or sensor replacement to $680 for a control board replacement, loop detector excavation, or motor rebuild on a commercial operator. Post re-setting and sag correction, which are common after San Bruno’s wet winters, typically add $150 – $400 depending on the footing work required. Gate opener repair specifically runs $280 – $520 for most residential units. We provide a written quote before any work starts, and the price we quote is the price you pay. We don’t start a job in San Bruno without your approval on the number. Call (833) 842-7897 for a free estimate on your gate, and we’ll give you a real figure, not a placeholder.
We Also Serve Cities Near San Bruno
Beyond San Bruno, our team covers South San Francisco, Crocker-Amazon, Excelsior, and Outer Mission. Homes in those areas share similar soil, fog, and housing stock, and we apply the same diagnostic approach whether we’re re-setting a heaving post or rebuilding a corroded control panel.
Serving San Bruno, CA – Our Local Coverage Area
We’re based in the San Bruno area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in San Bruno
In most San Bruno cases, the gate itself is binding because clay soil has heaved the posts, especially in the flatlands near San Bruno Park. The operator then strains and may trip its internal overload sensor or burn out a capacitor. We check post plumb before touching the operator; if the post has moved, we re-set it and realign the gate. If the post is straight and the gate swings freely by hand, then the fault is in the operator, usually the control board or a limit switch. Either way, the repair starts with a diagnosis, not a guess. Call (833) 842-7897 and we’ll walk you through what we’re seeing on-site.
Yes. Older automatic gates in San Bruno that predate current safety standards can be retrofitted with photocells, safety edges, and updated control boards that support them. We’ve done this on older LiftMaster and Linear units without replacing the entire operator. The retrofit typically costs between $180 and $420 depending on how many sensors the gate needs and whether new wiring must be run across the driveway. For a child, a pet, or a delivery driver near a gate that won’t reverse, the retrofit is worth it. We’ll give you a firm quote before we start.
We repair LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. In San Bruno specifically, we see a lot of older LiftMaster and Linear residential operators on the flats plus FAAC and BFT commercial units at multi-tenant properties. Our technicians are trained on the quirks of each brand, so we’re not ordering parts and hoping they fit. The diagnosis comes first.
San Bruno sits in the fog belt, so wood gates absorb moisture from the air all summer and from rain all winter. Redwood and cedar gates swell when wet, and if the gap between the gate and the post or the ground was already tight, the gate binds. Once the wood dries in a warm spell, it shrinks and the gate swings freely again. That seasonal cycle also loosens hinge screws and wears out the operator over time. We can plane or re-hang the gate, reinforce the hinge mounting points, or in some cases replace the gate leaf with a composite panel that won’t swell. A typical re-hang or planing job in San Bruno runs $180 – $320.
If the operator is under 15 years old and the motor is sound, replacing the control board usually makes sense; board replacement in San Bruno runs $260 – $480 on most residential units. But if the motor is also worn, or if the operator predates current safety requirements and can’t be retrofitted, replacement is often the cheaper long-term answer. We’ll tell you honestly which route makes sense for your specific unit, and we quote both options so you can decide with real numbers in hand. Call (833) 842-7897 and ask for a full diagnostic; we’ll give you a written quote on both repair and replacement, and you choose.
Call for a Free Estimate in San Bruno
If your San Bruno gate is stuck, dragging, or refusing to respond, don’t force it; a gate under tension can fail suddenly and cause injury. Call (833) 842-7897 and speak directly with a gate technician who knows San Bruno’s soil, fog, and older housing stock. We provide free estimates, written quotes before any work begins, and honest advice on whether to repair or replace. Whether you’re off El Camino Real or up in Mills Park, we’ll take the call, diagnose the problem, and get your gate working again.
Written by Clay Rasmussen, Owner at Gate Repair Crocker-Amazon, serving San Bruno and surrounding areas.